Metal Siding Painting Advice

Painting metal and aluminum siding can become a nightmare if not done right. Over the years I have worked on and repaired many homes with metal siding. Metal siding is real common in mobile homes. Most older mobile homes use aluminum paneling for their exterior siding.

Most painted metal siding seems to last at least 20 years. The reason for this is the paint is baked on in a factory giving it a high quality and nice looking surface. This baked on method is used for painting aluminum and most metals siding that gives the product a long life.

I lived in a mobile home park for a few years and my next door neighbor's mobile home had never been painted and was over 45 years old. He would go out and washed the mobile home once a year with some TSP soap while using a brush on the end of an extension pole to clean the home.

His mobile home might not have looked brand new but it was definitely in great shape. Over the years he had developed a few scratches and some dirt that was hard to wash off but that was about the extent of the damage to the painted metal siding.

Well we painted our mobile home and used an expensive metal primer along with some expensive paint from Dunn Edwards & Co... This paint worked great. We lived there for around four years and never had any problems once the home was painted. Having been in the construction business I knew we had to use a good metal paint primer in order for the paint to stick to the baked on paint process for the metal siding to look good.

Here's my advice to you when painting metal siding.

1. Make sure the metal siding is clean. Use TSP soap along with a scrub brush and scrub that baby clean. The cleaner the metal surface the better the new paint primer will stick or adhere to the old paint.
2. Follow the instructions carefully on the paint primer can when applying the primer. Do not paint below or above the recommended paint temperatures.
3. Make sure you explain to the paint salesman at whatever store you're in that you are going to be painting metal siding. Get the right paint primer.
4. I would love to recommend a paint primer but cannot because I don't want to get a phone call from anyone a few years from now telling me the paint is peeling off of their home. Let that responsibility become the paint manufacturers.
5. Let the paint primer dry for the recommended time as per the directions on the paint primer can. I prefer letting the paint dry at least one week. The reason for this is some paint primer's stay soft for a while and if you paint over them immediately they doesn't seem to bond as good and sometimes will stay soft for a long period of time.
6. Apply your final coats of paint following the manufacturer's instructions on the paint can.

There you have it painting metal siding is all in the preparation of the surface you are painting.

Have fun painting and always read and follow the manufacturer's recommended instructions for the products you are using. These people test their products constantly and know the best way to apply them to any surface.

Greg Vanden Berge is working on the internet to promote the education for creating simple to follow guides and home building books to help professional building contractors as well as the weekend warriors. He is currently working on more Building and Remodeling Library and adding useful content to help solve problems created by the lack of construction knowledge in the building industry.

Visit us and get more information on different Types Of House Siding

Home Repair Books
Lower Stairs

The Importance of a Home Inspection

First off, for all of those whom do not know, a Home Inspection is where a person or persons hire a Professional Inspector to inspect a property in which they have interest in no matter if they are on the buying side or selling side of the transaction. The majority of the times Home Inspections are ordered by the Buyers of a property but over the last couple of years Sellers have been getting inspections to help market their property for a quick sale.

Buying a home is a decision which is probably the most expensive decision most people will make in their lifetime. Unless one is familiar with all of the different phases of what is involved in the entire construction process, that decision to buy a home could be a very costly mistake. We are talking thousands of dollars or even hundreds of thousands of dollars just because the home was bought on emotion. That is why the Home Inspection is so very important.

Lets briefly run through the entire real estate transaction of a young couple buying their first home and they don't get their new home inspected.

Young Couple meets Real Estate Agent and tells the agent the size and type of property they would like to purchase. They go out looking over the next couple of weekends and they look at a dozen properties and then they see the one, the home of their dreams. They can't wait to get back to the Agents office so they can write up an offer and get things moving. They get to the negotiation part of deal and they are overwhelmed because the sellers have trimmed $5000 from the original asking price. The young couple thinks they are getting the house of their dreams at a great price and accept the seller's final asking price. In most cases their completed contract starts a 10 day inspection period (although that is negotiable); however the couple has looked at the house and didn't see any problems of any kind so they decided to not pay the $250 for a Home Inspection although the Real Estate Agent explained to young couple of the importance and value of an Inspection. The Agent got them to sign a waiver on the Buyers Inspection Sellers Response and life was good for the young couple.

They moved in and after a couple of weeks they discovered a water stain on the living room ceiling. They run to the window and looked out and it was a beautiful sunny afternoon and their first thoughts were it was raining. The couple had no idea what to do so they started looking for and calling plumbers from the internet and yellow pages only to find out because it was a holiday they were hard to locate all the while the stain continued to grow and the drywall began to bulge. They located a plumber and summoned them on their way but he was a couple of hours away. The drywall ceiling continued to bulge until it just could not hold any more water. At last it burst and water fell from the ceiling, along with drywall and insulation, down into the living room onto their brand new LCD TV and caused several thousand dollars in water damage by the time the plumber got there to shut the water off. The poor couple was now faced with thousands of dollars in repairs because they did not know a few things that a Home Inspection would have found.
If the couple would have spent $250 on a Home Inspection they would have known a few things that could have saved them the thousands of dollars they now face with repairs and damages.
The first thing they would have known, is where the main shutoff valve was for the water so they could have limited their repair cost to the leak repair and the ceiling drywall repair which would have probably been a couple of hundred dollars.

The next and probably the most important part thing they would have know if they had an inspection, would have been that the house was plumbed with Polybutylene piping which is known for its many problems and there were thousands of lawsuits from homes that had the piping installed. There were rebates offered and assistance was given for people to re-pipe their homes because this piping had so many problems. The Home Inspector would have most likely caught that and informed the young couple of the piping and would have probably recommended that it be re-piped and they could have made a more informed decision on purchasing the house. If they still wanted the house, they could have renegotiated the price with the seller to have the re-piping done.

Now their $5000 off of the list price which the seller dropped during their negotiations is not looking so good because now they have the cost of the re-piping and repairs which far outweighs that.

That is just a small example of what would have been found in the Plumbing phase of the inspection and a full Home Inspection covers all phases of the construction process such as Electrical, Heating and Air Conditioning, Structural, Foundation, Roofing, Attic, Fireplaces, and so much more.

Please don't let this happen to you if you are buying a home, or to someone you know, and Real Estate Agents, please print this article out and let your clients read it if they are thinking of foregoing an Inspection.

Have your Home Inspection done by a Certified Home Inspector in your State.

Ricky Wells is a Certified Home Inspector in Arizona. He owns and operates Premier Dream Home Inspections in Mesa Arizona. He has been inspecting homes since 2004 after years of experience in the many areas of construction such as Construction, Electrical, Plumbing, and Heating and Air Conditioning.He specializes in Maricopa and Pinal County. Please visit his website at http://www.pdhiinspections.com or you may email him at rwells63@pdhiinspections.com.

Remove Tree Sap From Your Paint

Removing tree sap (Gummosis as defined by Wikipedia) from your car's paint is generally a very difficult and time consuming task.
Here are some tips and tools that are very effective and safe ways to remove tree sap.

1) You need to remove the bulk of the sap from the paint without damage to your paint. The most effective and safe
method is to use a wood paint stirring stick. These are the flat wood sticks given to you free every time you buy house paint.
These work well because they are soft enough to not seriously scratch the paint yet they have nice edges that can grab the sap
and scrape it off. Be careful not to get too aggressive with your scraping if you care about the paint.With
enough force, you could do some damage to your paint.

2) Remove the remaining residue with full strength Simple Green or Goo Gone. I have purchased a number of Tar and Sap removers that are made for this
but so far, I have found full strength Simple Green or Goo Gone to do a better job and seems to be safe for your paint. Now, this does
take a fair amount of rubbing with pressure to completely remove the remains of the sticky sap. Use a soft clean rag or
cloth and apply the Simple Green to the cloth, then rub like crazy! An old sock works well.

3) Finally, apply a cleaner wax to the entire area that you worked on. In many cases, this is a number of areas on your roof
trunk and hood because you parked under a nasty tree that was raining sap onto your car. With that, you should probably
go ahead and wax the entire car... What else are you going to do on a Sunday afternoon? You may need to use a
mild rubbing compound or a cleaner wax with a mild abrasive to eliminate any minor scratches created from step 1.

Gummosis on your windows - The easy part.

Any tree sap on your windows is easily removed with a razor blade. This is the easy part because you can scrape it
all off in one pass without a worry of damaging the glass. Make sure to use a razor
blade holder so that you do not cut your finger off and really make it a bad day!

Dean Chafee, owner and creator of http://www.HowToFixYourStuff.com A community of People Helping People Fix Stuff.
Dean is also a contributing expert at Experts-Exchange: http://www.experts-exchange.com/M_3706695.html

Condo and Apartment Remodeling

With an urban area that is among the largest in the world not only in terms of size but in growth of most every industry, New York is 'the place to be' for many people. The ever increasing sprawl in the Big Apple has caused the housing costs to be well beyond the economic reach. This brought rise to the popularity of apartment and condo complexes. In the life of these living units, changes may be needed. Remodeling condo and apartment complexes is ideal not only for tenants wanting to boost property value but also for new owners wanting to inject their own style into their living space and those already living for years and want something new without the hassles of moving into another place.

Condo and apartment remodeling is not an easy task, especially if you are aiming at a project involving the exterior. Such real estate pieces makes use and share common facilities such as heating systems, elevators, hallways and other areas outside personal spaces. Changes on such facilities are generally not permitted.

For larger projects with planned exterior renovations, you have to consider several paperworks before getting on with the condo and apartment remodeling job. First off, researching on the governing rules imposed by the home owners association with which your space may fall under is vital. As these types of living spaces consider a harmonious look an important aspect in the selling point, some changes may or may not be permitted. Not following these rules may lead to higher costs including added maintenance in adapting the original facility design or liability to the association. Other documents that need to be acquired for large, external remodeling may include the architectural blueprints, building contract and a city's permit application.

Typically, minor NYC condo and apartment remodeling that involves only the interior including changes in the non-structural walls does not pose any issues with homeowners associations. As spaces in these living units are often limited, there are certain renovations that may be done to make the area seem larger and keep things better organized. Creatively adding new cabinets can help in minimizing everyday clutter. Recessed lighting can also add to the illusion of having a much spacious area. There are many things that you may do to your condo or apartment to match it with your lifestyle and taste. This includes soundproofing an area or the whole living unit, repainting, adding conventional appliances, renovation of kitchens and/ or bathrooms, and lighting.

In condo and apartment remodeling, another important thing to consider is hiring a reputable NYC contractor. Whether the project would be big or small, letting competent hands handle the dirty job would prove extremely beneficial especially if you are not a contractor yourself or have no idea and experience at all about fixing things. You would be saving more time and would be able to enjoy the changes in the littlest time of wait possible. Money is always a big issue, but with an able NYC contractor, you are assured of lesser mistakes, minimized risk of having back-jobs and lesser costs in maintenance.

Eugene Makeev has been in the home improvement industry for a while. His skills and expertise, which have been polished through time, are now used to help New York home owners avoid the common pitfalls in home improvements by matching their needs with the right, prescreened NYC contractor. To know more about NYC apartment and condo remodeling, visit Contractors New York.

New Concrete Crawl Space Access

Going Green in the Bathroom Benefits - Poway Home Tips

The tough housing market, tight lending practices by commercial institutions and across the board depressed economy is forcing more and more homeowners to be more frugal. Going green in the bathroom is one way many have found to save money in their energy and water bills. Many are still under the old idea that environmentally sustainable practices are expensive while in reality it is the opposite. The centerpiece of green bathroom remodeling is to save water and energy resources, while saving you money and us, the environment.

As consumers demand for products that have the twin advantages of saving money and natural resources increase, companies respond by making products that address these needs. Today, more and more companies are jumping into the bandwagon of making green products. The result is that the cost of these materials that are environmentally sustainable have gone down while their benefits have been appreciated more.

With bathrooms, it is much easier to go green than the other rooms in the house. By just following the 1994 water conservation mandates, many homeowners have simply replaced outdated fixtures and reaping the savings in utility bills immediately.

Going green in the bathroom benefits:
According to Mike Nagel of the National Association of Home Builders and Remodelers Council, "Americans spent over $230 billion last year on home remodeling, with energy efficient and sustainable products representing an increasing share of the market."

Low flow shower heads can dramatically reduce the amount of water used while taking shower.
Toilets that use less water than the standard toilets are becoming more popular. Dual flush toilets save water and have become the darling of some in the bathroom renovation business.
Bathtub and sink refinishing are lees expensive than total tear out. Reglazing a bathtub saves money, time and the environment.

Take for instance, a bathtub. It costs about $300 to buy a new one, but when the price of tear out, plumbing, tile setting and disposal of the fixtures, the price adds up pretty quickly. The price for total bathtub replacement can go from $1500 to $2500, depending on the part of the country the work is done. Bathtub refinishing is done in the bathroom, takes about four hours to complete, can be used the next day and costs about $450. Restoring a bathtub while in the bathroom, saves the energy that could have been used in manufacturing, and transporting the tub to the warehouse, store and to your bathroom. It also saves the landfills.

Going from the standard bulb to a low energy bulb saves money on utility bills. Using recycled or re-manufactured flooring materials saves valuable assets. Paints that are low in VOC have health and green benefits. Reducing volatile organic compounds (VOCs), will reduce health problems, from asthma to cancer. Be careful to use building materials like cabinetry, adhesives, caulks and paints that are VOC free.

Because the bathroom is affected by heat, humidity and chemicals from cleaning, hygiene and cosmetic products, ventilation, therefore becomes very important. Outside air is less polluted than the air inside. If it feasible to have a window that recycles the air in the bathroom, go ahead and enjoy your fresh air. Going green in the bathroom saves money, time, the environment and is a healthy thing to do.

Wilson Uche Ukah, is the President of Refinishing Stars, a bathtub refinishing company serving homeowners in Atlanta, Chattanooga, Nashville and Knoxville. Refinishing Stars, refinishes bathtubs, sinks, and countertops for hotels and motels nationwide. He writes regularly on green remodeling. Wilson can be reached at http://www.refinishingstars.com or sales@refinishingstars.com

Structural Crack In Brick Wall

Tract Houses Framing Problems

The house you live in was probably a mass produced home built as part of a housing track. The track home is a rapidly built house in phases. These phases if possible will over lap the other home building trades. If possible you will have the plumbers working on the same house as the electricians and the framers. This is called fast tracking.

Fast tracking a house is building a home as fast as humanly possible. So you can imagine the pressures put on all of the people involved in building a track home.
The pace is so fast sometimes that I have seen job superintendents and foremen look like they were actually going to blow up. I mean explode from the pressure they where under.

Framing the stairs on the job was the same experience for me most of the time. Sometimes I had three jobs going at once. Think about it. At the most, I could only go to each of the jobs twice each week. That involved working on Saturday of course. This made a lot of framing foremen extremely upset. They had full time crews on their jobs always working five days a week. If I missed one day of work. I was behind for the rest of the job.

Now it rarely happened but if I did miss a day of work I had to make it up some how. The only way to make it up was by working late or on Sunday. Well most of the time I worked six days a week from 7:00 in the mourning until 5:00 at night. So working late meant sunrise to sunset. Oh did I mention that I did have a family. This wasn't easy for them either.

One time I got so far behind on a job that I was putting stairs in while they were roofing the houses. Talk about one unhappy foreman. I think you get the idea about the pressure I was under to install these stairs on time. My experience building stairs on track built homes taught me to build homes extremely fast while being proficient.
I'm not interested in working like that anymore. My life is simple now and I want to keep it that way. The next time you see a construction worker working late on a Saturday show some compassion. Maybe by reading this article you will understand some of the pressure he is under.

Building tract homes is hard on you mentally and physically.

Happy Home building.

Greg Vanden Berge is working on the internet to promote the education for creating simple to follow guides and home building books to help professional building contractors as well as the weekend warriors. He is currently working on more building stairs books and adding useful content to help solve problems created by the lack of construction knowledge in the building industry. Stairway Safety

Interior Corner Windows

Repairing a Leaking Toilet - Home Repairs

Let me explain how a toilet works. First when you go to flush the toilet a little arm pulls a rubber flapper up and lets the water drain into the toilet bowl. The water draining into the toilet bowl forces the old water out along with the number two or number one waste and extremities.

If the toilet sounds like it is running there is a good chance that the seal between the rubber flapper and the plastic rain at the bottom of the toilet is broken somehow. The sound you are hearing is water running around this ring and in to the toilet bowl.

This leak is actually causing no damage to the toilet itself but is wasting water. Hence the water bill will be a little higher if you don't fix the leaking toilet. The best way to find out if this is actually your problem is to take the toilet tank lid off. Then stick your hand down into the toilet bowl and press gently on the rubber flap.

If the water stops leaking or starts running faster this is your problem. Turn the water off to the toilet. There will be a shut off valve on the wall under your toilet bowl in the bathroom. After you turn the water off removed the plastic flap and examine it.

You will be looking for a warped toilet flap or of some sort or grooves on the flapper itself. Take the toilet flapper down to your local home improvement store and buy a new one. Go home and replace the new toilet flapper and this should solve 90% of your leaking toilet problems.

There is one more thing it could be. With the toilet tank lid off, check to see if water is overflowing into the little round plastic pipe. This plastic pipe should have a small hose running from the float valve assembly into it.

If the water is over flowing from the toilet tank into this little plastic pipe you will need to adjust the float.

First thing you will need to do is while the toilet is running lift up on the float lever arm. If the water stops you can simply bend the metal arm of the float lever. The purpose of bending the arm will force the float deeper into the water there for stopping the water from rising over the small tube in the center of your toilet.

There are few parts to a toilet and most parts can be purchased at your local hardware or home improvement centers. Toilet repairs like this can be made simple and the parts used to replace are inexpensive.

Happy Toilet Repairing.

Greg Vanden Berge is working on the internet to promote the education for creating simple to follow guides and home building books to help professional building contractors as well as the weekend warriors. He is currently working on more House Building and Remodeling Library and adding useful content to help solve problems created by the lack of construction knowledge in the building industry.

Visit us and get more information on building and remodeling your homes and Some Great Plumbing Ideas

Home Security Books

Install Kitchen Cabinets - House Remodeling Ideas

One of the best ways to economize on your kitchen project cabinets, thank about installing on your own.

If you have the correct hardware with some strategic planning, the procedure is really quite simple.

You will need to make up a plan to successfully attack the installation of you your kitchen cabinet with a friend or partner, though, because it's very difficult to position those cabinets alone.

Continue to study this to learn the information about how to easily install kitchen cabinets by yourself!

* Before anything else, assemble the cabinets employing the instructions that accompanied them.

* Employ a pencil to lightly mark the cabinet positioning. Insure that they will be level and will not interfere with your electrical outlets, will permit you to use your current plumbing, and things if this nature. How dreadful would it be if you found when your installation was complete you determine that your sink doesn't fit..

* It does not matter hardly at all, you can choose to install the wall or the floor units first. Included instructions direct you need to install the units of the floor first, however if you are more comfortable you can do it the other way around.

* Employ a stud locator to find the studs for each cabinet. Make certain to fasten the cabinets to the studs, and use cabinet screws instead of using drywall screws. Drywall screws just can't cope with the weight of kitchen cabinets.

* Bore guide holes. This prevents your cabinets from splitting and results in the cleanest joins.

* Fasten the cabinets to the wall studs employing a cabinet screw at the top and bottom of the cabinet unit. For sturdier cabinets, it's a very good idea additional to screws to buttress the weight.

* Examine each cabinet to make sure that it's level before securing it to anything. It could be necessary to add filler material like wood slats or tile underlayment beneath the units to insure your cabinet's level.

* Set the corner cabinets first, since it will be impossible to move the wall if you end up with less space than anticipated! Subsequently install the other units around them. If you have voids between the units or need to adjust one down to allow for the wiring or plumbing, place a wood panel in-between the units.

* When you're ready to install non-corner units, it would be a important idea to fasten them together, and then attach them to the wall. This assures that the front panels are flat and flush with each other.

* In the case of wall units, the procedure is nearly the same, however if you have really sturdy ones, you will most likely need to employ wood pieces called "shims" beneath them to help underpin the bulk.

* You may choose to employ a friend or partner to help hold up the cabinets, however if you followed the suggestion to connect your cabinets into a row before you put them up, it's going to be difficult to handle all that bulk. Experiment with stacking buckets or paint cans beneath the units to assist in keeping them up there. You should still to have your helper hold tightly; it would be really despicable if they fell over and were blemished or fractured

* Once you have got all of the screws into place, you will need to carefully remove the supports.

Complete Renovations | Home Improvement Loan | Home Decorating | Kitchen Backsplash | Public Designs

Install Kitchen Cabinets - House Remodeling Ideas

One of the best ways to economize on your kitchen project cabinets, thank about installing on your own.

If you have the correct hardware with some strategic planning, the procedure is really quite simple.

You will need to make up a plan to successfully attack the installation of you your kitchen cabinet with a friend or partner, though, because it's very difficult to position those cabinets alone.

Continue to study this to learn the information about how to easily install kitchen cabinets by yourself!

* Before anything else, assemble the cabinets employing the instructions that accompanied them.

* Employ a pencil to lightly mark the cabinet positioning. Insure that they will be level and will not interfere with your electrical outlets, will permit you to use your current plumbing, and things if this nature. How dreadful would it be if you found when your installation was complete you determine that your sink doesn't fit..

* It does not matter hardly at all, you can choose to install the wall or the floor units first. Included instructions direct you need to install the units of the floor first, however if you are more comfortable you can do it the other way around.

* Employ a stud locator to find the studs for each cabinet. Make certain to fasten the cabinets to the studs, and use cabinet screws instead of using drywall screws. Drywall screws just can't cope with the weight of kitchen cabinets.

* Bore guide holes. This prevents your cabinets from splitting and results in the cleanest joins.

* Fasten the cabinets to the wall studs employing a cabinet screw at the top and bottom of the cabinet unit. For sturdier cabinets, it's a very good idea additional to screws to buttress the weight.

* Examine each cabinet to make sure that it's level before securing it to anything. It could be necessary to add filler material like wood slats or tile underlayment beneath the units to insure your cabinet's level.

* Set the corner cabinets first, since it will be impossible to move the wall if you end up with less space than anticipated! Subsequently install the other units around them. If you have voids between the units or need to adjust one down to allow for the wiring or plumbing, place a wood panel in-between the units.

* When you're ready to install non-corner units, it would be a important idea to fasten them together, and then attach them to the wall. This assures that the front panels are flat and flush with each other.

* In the case of wall units, the procedure is nearly the same, however if you have really sturdy ones, you will most likely need to employ wood pieces called "shims" beneath them to help underpin the bulk.

* You may choose to employ a friend or partner to help hold up the cabinets, however if you followed the suggestion to connect your cabinets into a row before you put them up, it's going to be difficult to handle all that bulk. Experiment with stacking buckets or paint cans beneath the units to assist in keeping them up there. You should still to have your helper hold tightly; it would be really despicable if they fell over and were blemished or fractured

* Once you have got all of the screws into place, you will need to carefully remove the supports.

Complete Renovations | Home Improvement Loan | Home Decorating | Kitchen Backsplash | Public Designs

Supercharge Your Water Heater

Have you ever had to stand shivering in the cold morning air waiting for hot water with your arm outstretched, fingers extended into the cold stream of water. It seems to take forever for the water to get hot. Speed up your hot water with a hot water circulating system.

Traditionally, if you had a hot water circulating system, it meant that you had a hot water pipe that ran in a big loop from the outlet of the water heater to each fixture one after the other, and then back to the inlet of the water heater through a small pump. By continuously pumping water through the loop you have instant hot water at every fixture.

This is very convenient. Hotels and motels have hot water circulating systems; otherwise it could take hours to get hot water with such long pipes as they have.

However, instant hot water is also very expensive. Not only do you have to pay for the energy to run the pump continuously for long periods of time or even full time, but you also have to pay for the heat energy being radiated into the environment from that big loop of hot water piping. The cost of heating the water is considerably more than the cost to run the pump.

There are a number of manufacturers producing hot water circulating systems that utilize the cold water line as the hot water return line.

Some of these pumping systems use small pumps that pump water very slowly, and are temperature controlled. The pump turns on when the water temperature drops below a set point, and then shuts off when the water temperature in the pipe reaches another set point. This keeps the water your entire piping system full of luke-warm water. The water is warmer near the water heater and colder the further you get from the water heater, but it is tepid through out the piping system.

Most folks don't really want the cold water pipe full of warm or tepid water. You don't get "Instant Hot Water" as the manufacturers claim. I think they should be honest and call them "Instant Tepid Water Systems". The Lang Auto-Circ and The Grundfos Comfort System are two such systems, and the Hot Water Lobster is another. The Hot Water Lobster doesn't have a pump, but relies on the fact that hot water rises, and the Lobster valve has to be substantially higher than the water heater for the system to work.

Unfortunately these systems consume much more energy since you are heating that big loop of piping and return line and its surroundings. The cost of the energy will far outweigh any monetary savings from the water conservation aspect.

Another class of systems that use the cold water line as the return line is the "Hot Water Demand Systems". These systems only pump the water to the fixture when hot water is "demanded" by the user. The pumping costs are small; typically demand systems use less than $2.00 per year in electricity costs. This is because they run for such a brief time, typically less than 1 minute per use.

When the user turns on the pump it runs until hot water reaches the fixture and then the pump automatically shuts off. The cold water line does not end up full of warm water.

With the demand system the energy consumed is no more than if the user just ran the tap as normal. Hot water is not being circulated. And since the hot water is not being circulated it does not affect the life of your tankless water heater or the warranty.

The water is pumped more quickly than if you ran the faucet full throttle. You save time, water, energy, and money!

There are at least three manufacturers of demand systems, Metlund, RedyTemp, and Chilipepper. The Chilipepper will run any tankless water heater. Some models of the Metlund system will run tankless water heaters, and some won't, so be sure to inquire before you make a purchase. The RedyTemp will not work with a tankless water heater.

Choose the type of system that best suits your needs and enjoy the added convenience of quick hot water while being kind to the planet.

For free information about water heaters and hot water circulating systems, visit Mr. Lund's website: All About Water Heaters Mr. Lund also has a website for information about making money online: Lund One - Make Money Online

Contractor In Southern California

So you want to make big money making a living as a contractor in the state of California. Well now I bet you have seen contractors on TV or maybe you know someone who is a contractor. You see these men and women playing the part as Mr. or Mrs. Money bags. If you have the slightest thought that becoming a contractor will provide you with a life of riches think again.

Most contractors that I know and have worked with over the years don't think of there jobs as easy. They have to work everyday and a lot into the night doing estimates or meeting with potential clients because they are to busy during the day. The life of most contractors in the beginning will be difficult to say the least. But if successful you will make a great living for yourself and your family.

Now that we got the false illusion of the contractor answering his cell phone all day at some nice golf course having lunch talking about the money that he just made selling his oil stocks. We can start on reality. If being a contractor was that easy everyone would be a contractor. Right..... Well maybe not everyone.

I have been a contractor for over 22 years and in construction for 30 year. I have seen a lot of changes over the years. I remember when a few contractors that I worked for made a lot of money during the late 1970's. These guys had Ferraris and money to burn with one exception they had no idea how to save any of it. These guys went on vacations and bought extravagant toys for them selves. Out of most of the big framing contractors I worked for about 10 percent are still in business or actually saved their money during the good times so that they could make it through the bad times.

These contractors never thought it was going to end. Life on easy street that is. But it did and most went by the way side. I guess that is the nature of business. Especially the current economic business cycles that we seem to go through over the years. If you don't have the money to advertise or carry a payroll. Your business is going to suffer during the bad times. Sure there is credit and bank loans but you still have to pay that money back. IF you can't save your money stash some away for advertising.

Some of the best advice I can give a contractor anywhere especially in the state of California is " Don't Think The Great Times Of Easy Money Will Last Forever". Save some of the money you make just in case you need to get through the bad times. You will thank me for this latter, Some time down the road. Take this advice and put it into action starting right now.

Greg Vanden Berge has over 30 years of experience in residential home building and remodeling. This provides you with the comfort of knowing that you have a professional with the knowledge and skills to complete your construction projects in a timely manner.

Our low overhead along with our new online estimating system will provide you with the most competitive construction pricing in the area. We continue to educate ourselves about the new home improvement books and building systems in the construction industry. If we have any doubt that something might not work we don't use it. We have found some of these products to be the root of some major home building problems.

Click on the Home Remodeling Ideas to get more information and a possible online estimate for your home improvement project.

Top Stair Handrail Inspection

Bathroom Moisture Problems - Home Remodeling

Right above my bathtub in my master bathroom the paint is peeling off the wall. The area is peeling above the tile in my bathtub and shower combination. I tried to glue the peeling paint back and only made the situation worst.

First things first. The paint is peeling because there is to much moisture in the bathroom while you are using it. Do you have any windows you can open or a ventilating bathroom fan. If you have a window crack it open part way while you are showering.

The water droplets will accumulate on the walls and drip into any cracks. Right above the tile grout is a great place for moisture to accumulate. Oh yeah moisture loves grout and drywall. If you have any unpainted areas or an area that has cracked. Guess what you have now.

Your paint is peeling because the bathroom gets hot and cold. Moist and dry. If you have the door and windows shut. You just created a moisture trap. Most people prefer their privacy and will closes the door when using the shower. Well then open the window and let some cold air in while you are taking a nice warn shower. I don't think so. Most showering fools don't like that idea either.

Ok one more idea keep the windows shut so you don't let the cold air in. Then lock the door so no on barges in on you. If you have a ventilation fan turn it on. This will at least pull fresh air in from under the door and send the moist air out of the house.

But the fan is so noisy and I can't enjoy my nice warm vapor producing shower that will eventually cause me to get sick from mold particles floating around in the air while I am using my bathroom.
Does this about sum it up for you and don't we all do this from time to time. We want to enjoy our shower time, so we close up everything and when we are in our bath sauna environment relaxing our house is getting some damaging moisture that could cause mold and mildew.

Open a window or door a little when you shower. Get some air circulating through the bathroom and prevent damage to your nice house.

Put up with a little inconvenience for you homes sake and your pocket book.

Greg Vanden Berge has been in the home building and remodeling business in California for over 30 years. With this knowledge he has created a few websites that provide useful information for home owners as well as contractors. His main goal is to educate professionals in the home related businesses, dealing with problems that can easily be avoided with just a little bit of information.

His website provides all kinds of answers to remodeling and new house building in North San Diego Home Remodeling Carlsbad Home Remodeling

Visit us now for Bathroom Ideas

Repaired Plywood Bathroom Floor

Dual Pane Window Glass Repair

For the past few weeks, I have been explaining how to repair a broken window pane in your home. But, what if you have dual pane windows? Is the process the same? Well, pretty much, except for a couple of variations. So, let's review the single pane repair process, and I will point out the differences regarding dual pane windows.

When we start talking about dual pane windows, one of the first things that comes to mind is vinyl window frames instead of aluminum. When dealing with dual pane windows, you can have either aluminum or vinyl frames, depending on the year the house was built. Dual pane glass got popular in the 1980's, but vinyl frames didn't really catch on until the 1990's. So, if your house is less than 10 years old, chances are you have vinyl framed windows. In either case, I will discuss the differences. Let's say you have a sliding aluminum frame window with dual pane glass. The procedure for removing the frame from the opening and the glass from the sash is the same as with the single pane windows.

The differences are, first, the glass goes into the frame about twice as far as the single pane window. The single pane window glass went 1/4" into the surrounding rubber. The dual pane usually goes 1/2" into the rubber. So, if both pieces of glass have been broken, you are going to have to order a new IGU (Insulated Glass Unit) from the local glass shop. They are going to want to know the width, height, overall thickness, and possibly the individual glass thickness. The best way to get the dimensions is to measure the width and height from rubber to rubber, write those numbers down. Then, remove the panel from the opening and place it on a table like we did with the single pane window. Remove the screws from opposite corners and pull of the frame. You will be able to see how far the glass goes into the surrounding rubber. If it's 1/2", then you want to add 1" to the width and height that you measured previously (1/2" times two sides= 1"). Then, measure the overall thickness of the unit by removing the rubber from the glass edge.

Typically, this dimension is 1/2", but not always. There is a metal spacer that divides the two panes of glass. Make a note of the color so you can request the same color in the new IGU. It's either going to be silver or bronze. If you want to get the same size spacer you need to give the glass shop the thickness of each piece of glass in the IGU. If the old unit has 1/8" glass on both sides, and the overall thickness of the unit is 1/2", then they will use a 1/4" spacer. If the glass is 3/32" on both sides, they will use a 5/16" spacer. If you don't care about matching the spacer thickness, you can request the thicker 1/8" glass, and they will automatically use a 1/4" spacer.

When you get the new IGU home, the installation is the same as the single pane window. Now, what if only one side of the IGU has been broken? Many times the outer pane will break, but the inside pane is fine. You can order a whole new IGU Like we just did, or, if you're the adventurous type, you can order only the single pane of glass that was broken and replace it. I'm going to explain how to do it, then i'm going to tell you the things that can go wrong. After you have the window pane on the table with the surrounding frame removed, you will see a black rubber type substance around the edge where the spacer is applied. This is a butyl sealant, and you have to separate the broken glass from this butyl. The best way to do it is to take a utility knife with a new blade and break through the butyl where it meets the broken glass. Then, take a new hacksaw blade, and push it into the area where you sparated the butyl from the glass. You don't want the hacksaw blade to be attached to a hacksaw. Using your hand, saw back and forth as you work your way around the edge of the glass. This should allow you to remove the glass.

Once that's done, lay rags on top of the good piece of glass to catch any debris, and scrape the surface of the spacer that will be contacting the new glass. Use a putty knife. Then, remove the rags and debris. When you are ready to put the new glass on, clean the inside of the good piece of glass that you didn't remove. Remember, once you install the new glass, any debris or finger marks on the inside will be permanently sealed. So, clean it real good and check it from all angles. Do the same to the side of the new glass that will be going to the inside of the IGU. Then, run a thin bead of clear silicone around the entire perimeter of the spacer. Set your new glass on the spacer and use finger pressure to adhere the glass to the silicone all the way around.Then, come in from the side, and run silicone around the side where the glass and spacer meet. Cover the window opening with something for 24 hours. You do not want to touch the IGU for 24 hours. The silicone needs to cure. After 24 hours, you can assemble the unit and install it back into the opening.

There are a couple of things that can go wrong. The first one is leaving marks on the inside portion of the glass. Once you seal the glass, you cannot clean what's between the panes. The other thing involves condensation between the panes. If you have even the slightest break in the silicone seal around the glass, chances are you will beging to see moisture form as soon as the nights get cold and the days get warm. You are going to have to decide if you are confident enough in your ability to do the job right, or if it's better to pay the extra money to have it done for you. Just because you pay someone to do it, doesn't mean you still won't encounter the same problems. The difference is, they have to guarantee their IGU for a minimum of 1 year. I have received many units over the years that had marks in between the glass. The beauty of it is the manufacturer can't dispute it, because there's no way anyone else could have done it except them.

OK, what if the window frames are vinyl instead of aluminum? Well, the main difference is the glass in a vinyl window no longer has the rubber gasket around the edge. You dont remove the opposite corner screws and separate the frame from the glass. What they do is put either silicone or a two sided tape on the lip of the frame where the glass rests. That's what holds the glass in the frame, then they apply a snap in stop on all four sides of the glass. So, you have to remove the stops first, then turn over the panel and break the seal holding the glass to the frame using a utility knife. Wear gloves during this procedure. If only one side of the IGU is broken, don't even think about repairing just the one side. You will never get that IGU out of the frame without breaking the other piece of glass in the process. But, on the positive side, you can remove the stops without taking the panel out if it's a slider. You can then measure the dimensions of the glass, and order the new IGU. That way you eliminate any need to temporarily cover up your window. The same is true for the stationary portion of a slider, or a picture window. Before you install the new IGU, be sure and clean the lip that had the tape or silicone, and apply either silicone or tape. Either will work.

You will discover that replacing an IGU in an aluminum frame window is a whole lot easier than a vinyl window. But, in either case, you can do it yourself and save a few bucks.

John Rocco has been installing replacement windows since 1978. To learn more, visit How To Install Windows

Drawbacks of a Gutter Guard System

Homeowners use gutter guards to prevent debris such as leaves and other particles from clogging the gutter. There are different types of products that people can choose from when purchasing from online stores. A homeowner can purchase them on online stores that sell home appliances or online superstores that retail home and other appliances.

These products should be in good condition, especially during the rainy season, to prevent rainwater from flowing down the walls of a home. One can hire specialized cleaners to do it for them if they do not know how to do it. Most companies that sell home appliances also offer cleaning services for a fee.

Copper Gutter Guards

These are the best for long term use because they do not rust and nor do they rot. Aluminum gutter guards, which are cheaper than most others, are strong. However, they rust when kept in poor conditions. During the winter season, most people experience problems with their gutters, as ice blocks the opening at the top. If a person does not get rid of them the moment they start to build up, then the water may flow over it or against the walls of a home. The freezing temperatures may cause the formation of massive ice dams, thus causing the entire system to over flood. Homeowners can avoid this by having companies install heater cables. This is a costly procedure. However, it is worth the effort and it saves a person the trouble of having to keep unclogging their gutters.

Besides the installation of heater cables, many people purchase gutter guards to prevent ice from forming at the top and falling into the system and blocking it. A homeowner needs to maintain copper gutter guards by purchasing and applying sealants on them regularly to prevent them from turning green. The green color is also called a patina. Some people like it and allow the metal to gradually turn green. Others prefer to maintain the original color and apply the sealant regularly.

Aluminum Gutter Guards

These products also have special sealants that a person may use to prevent them from rusting quite fast. Unlike the green patina, rust will materially impair the effectiveness of the aluminum. Protection and maintenance is important because it enables one to avoid incurring extra costs, which include repair costs or replacements costs. When selecting a suitable solution, one should mull over a number of things such as the circumference of the gutter, the design as well as their functional advantages.

Aluminum, by nature, can be have a natural useful life of about 10 - 15 years. This useful life will vary dramatically depending on several factors including the external environment, the galvanization used and the maintenance employed by the owner. For example, using aluminum products in a house next to the ocean that are not galvanized with some sort of corrosion-resistance coating and poorly maintained is going to have a much shortly lifespan than a zinc galvanized product located in a dry (desert) community with an owner who performs annual maintenance.

From a design perspective, not every product is suitable for every home. Homeowners should try to match gutter guards with the existing system and the type of home. For instance, homes made out of stucco match well with copper, while grey houses blend well with aluminum.

Plastic Gutter Guards

Plastic is another material used in the fabrication process. They come in various colors. Therefore, one can select one that matches their roof. Homeowners can also blend the roof with a gutter guard of a different color though the two should compliment each other. The shape of the product may make a home visually attractive or not attractive at all. This requires a person to compare their shape and that of the product in order to select a suitable piece.

In summary, there are three major types of materials that you can use for your solution, copper, aluminum and plastic. Each one has its own strengths and weaknesses.

To learn more about copper gutters, please read the following article at http://www.guttersa-z.com/Copper_Gutter.html It has information about copper gutters.

You can also find other valuable information about gutters, downspouts and more at http://www.guttersa-z.com

Bottom Stair Stringer Inspection

Prepare For New Trends in Bamboo Shades

As the growth of any product increases, there will be a deepening of the available options out there. Often, the newer choices will be the best. Imagine the time when the re were only a few choices of personal computers. Later, even now, there are so many options. Given this inevitable flow of new options for products, one should not be surprised that there are so many new choices of window treatments available. In addition to the wide range of product choices, there is a deep and wide range of style and design with each category. This article will focus on the options available for bamboo shades. The old style of sticks interlaced with threads, which may have had only a few color choices, but not many design options, is the past. Now, perhaps due in part to enhanced production methods, as well as a desire to match almost every design plan, has led to a time which may well be the renaissance of bamboo shades.

The new trends in bamboo shades have included a movement towards the unconventional. Traditional American consumers have gone for basic white in window treatments. While there have always been sales of white bamboo shades, woven woods consumers have usually trended more toward the unique patterns. This will include different types of slat materials as well as new weaving and interlacing of threads.

Basic stick design has been replaced by more bamboo looking materials. The bamboo shades which use tortoise shell patterns are now increasingly common. These bamboo shades sometimes are colored differently, including black or red, which makes for a different type of color splash compared to the traditional greenish brown colors. Other designs use different sections of the split bamboo as the base. Much of this material was considered not attractive enough for bamboo shades, but now, with new production techniques, as well as the other new trends discussed in this article, these former scrap discards are being used in a productive way.

While the basic brown, beige, or white threads are still available, the trends here are towards more durable threads, which will last longer under strong exposure to the sun light. Bamboo shades also use newer colors, including green, red, and chocolate, and this range can allow for a design that may have looked commonplace to now look rich and new. This slight change is usually not noticeable as to the cause, but upon close examination of the threads, one will notice that a simple difference in color is the cause of the style enhancement for the bamboo shades.

The third most common way in which bamboo shades patterns are evolving is a new style of weaving the threads. The traditional shades had a simple drop in the threads, with a weave that mimicked plain flat fabric. However, the newer designs include braids, macrame, and twists. The woven threads themselves are beautiful enough to make a window treatment. However, the blending with old and new bamboo sections makes for a new and crisp treatment, worthy of a design award when used in a fashionable living room.

As the trends for higher fashion design ebb and flow in bamboo shades, consumers will be offered a fine new array of exquisite styling. Consumers should try to learn more about these new designs, all of which are available in real bamboo for prices similar to the less expensive and less design focused plastic options. The online retailers are the fastest to the market with these choices, but the unfortunate loss in ability to touch the real material is worth the trade off when realizing such great high fashion bamboo shades for one's spaces.

Judith Persit works from home in a design studio and writes about bamboo shades Learn about shades at her website.

House Pocket Door Problems

Just a few months ago I went over to repair a pocket door that was closing at a weird angle. This was the first time I had ran into this sort of situation and was definitely confused. I got a flashlight and started looking inside the pocket door frame. I had a hard time finding the problem but when I did it was obvious.

As the pocket door was sliding closed it would work perfectly but when you went to open it the bottom of the door would stick out about an inch and a half passed the door jam. The problem turned out to be the track was missing a screw in the very back and as the door slid back into the frame the tracking would hang down at an angle from the weight of the door. There was no way to reach the screw because it was at that very back of the pocket door frame near the framing itself.

In order to fix the pocket door problem I was going to have to remove a good sized area of the plastered wall at the upper right hand corner of the pocket door frame. This was the only thing I could think of and would require a simple wall patch and some paint to make the repair complete.

This job took me about one hour to cut the hole and replaced the screw that had fallen out of the pocket door tracking. I then use some fast setting drywall plaster and some fiberglass drywall tape to repair the wall. This took another hour to finish the drywall properly.

Some pocket door problems are a little easier to repair than this one. Most pocket doors seemed to have problems sliding and eventually are left closed, never to be used again.

Painting the doors over and over again can actually add to the thickness of the door or excessive moisture in the home over long periods of time can also cause the door to swell preventing it from opening properly.

Painting the rollers themselves or the track that the rollers ride in can create a problem with rolling the door easily and effortlessly. If the pocket door rollers or tracking is damaged they will have to be repaired or replaced, obviously. Some people actually spray silicon on the rollers or grease the pocket door wheels and over time the track becomes caked with dried grease and dirt making the door hard to open and close

Here's one most people don't ever think about and yet I have faced this problem more than once. "The Dreaded Picture Hanger". Most people don't realize that the pocket door will not operate very well with a nail driven through it. I have had people complain about their pocket door not operating properly but they can wiggle it a little.

When I come upon a situation like this it usually just requires removing the nail that the picture is hung upon.

I have also seen instances where the home has been remodeled and new floor trim or door trim has been installed. The finish carpenter using his nail gun without changing to a shorter nail has himself nailed the pocket door shut. This could be a big problem because the nails are so thin they could be hard to remove.

Well that's all I can think of for pocket door problems that I have ran into for now. Until the next article have fun remodeling your home.

Greg Vanden Berge is working on the internet to promote the education for creating simple to follow guides and home building books to help professional building contractors as well as the weekend warriors. He is currently working on more Building and Remodeling Library and adding useful content to help solve problems created by the lack of construction knowledge in the building industry.

Visit us and get more information on building and remodeling your homes and Vista Door Repairs

Home Remodeling Books

Sink Water Filter - Discover the Dangers You Face Without One

Have you ever sat down to consider the many health benefits that you and your family could enjoy through the purchase and installation of a sink water filter? Many people still don't realize the dangers that they face every time that they pour themselves a glass of unfiltered tap water.

Do you realize that here we use around 80,000 industrial chemicals? Most, if not all of these harmful chemicals, have found their way by some method or another into our ground water supply. This means that traces of any or all of these chemicals may be present in your drinking water at home.

A high quality sink water filter is a necessity for your family due to the fact that there is no protection from these chemical contaminants that your local water treatment center can offer you. Their equipment is simply not designed to allow the blocking of these chemicals to be possible.

Of course they are also not able to stop the flow of certain parasites and cysts that are in our water supply either. You see, not every microbe is killed by the chlorine disinfection process that our drinking water receives. These parasites can cause serious harm to you if they are ingested.

A good sink water filter can protect your family from the harmful effects of all of these parasitic and chemical threats through the use of a four pronged system of filters. They are each designed to take care of a different problem area.

Let me explain to you exactly what is necessary in order for you to be fully protected.

What you need in order to rid yourself of all of the hazardous chemicals that are part of your drinking water supply are a multi block filter, and an activated granular carbon filter. These two are both necessary because of the vast array of the chemicals that are in our water.

Your sink water filter also needs to be armed with a sub micron filter in order to be able to rid you of the threat that is posed to you and your family by microscopic parasites and cysts. Your family can rest easy knowing that the threat that these microbes cause has been effectively abated.

Your system is not complete without the inclusion of a filter that will remove toxic heavy metals such as lead and copper from your drinking. An ion exchange filter is necessary in order to achieve this goal by trapping the traces of metal and replacing them with healthy electrolytes.

If you have a reasonably priced filter that employs all of the elements that I have mentioned in this article, then you and your family will be fully taken care of. But don't settle for anything less or there will still be contaminants present. You want your family to be as protected as possible.
Hopefully you now see what an integral role a sink water filter can play in your lives. There is no time like the present for starting your search for just the right model for you.

For free information on how to protect yourself from water contaminated with carcinogens, traces of drugs, hormones, parasites and other toxins click here Lauren Leddy is a consumer advocate and a dedicated researcher of health related issues. Visit her website now at http://www.safe-water-purifier.com and discover what she has learned that will help you select the very best water filtration system for your home or office.

Books on Home Building - Professional Advice

If you're a do it yourself or or a homeowner who every once in a while, once to tackle a small or large project but doesn't know where to begin, can gather useful information from home building books. I have been using these books for years and may have been worth their weight in gold.

I started my career working for my father and my father worked for his father as a Carpenter. Our job was to frame the house and we built a Lotta homes. I learned how to frame and developed some great carpentry skills from my father and working with other skilled carpenters. Over the years, if you're paying attention, even a monkey can figure out, how to assemble almost anything.

The only problem that I faced, was learning how to build the rest of the home. I would often ask questions to other building trades like plumbers, electricians, roofers and construction superintendents. Some of these people were helpful and others were not. When I was in my early 30s, I purchased my first book on home building. This book lead to other books and soon I found myself with more home building knowledge that my father.

I had about 50 books on home building and soon found myself doing large home remodels, with no formal education. I would attribute almost everything that I learned outside of house framing to books. These books have proven invaluable to me over the years and with a relatively small investment. I couldn't have spent over $200 purchasing these books but have used the knowledge from them to save myself thousands of dollars.

One $20 home building books or home repairs, can save you lots of money, if you're willing to do a little research and the labor to complete almost any home building project.

By the way, if you're interested in learning how to repair a roof, build your own house, interior decorating, structural engineering, building a deck, gathering some more information about home painting or even remodeling your bathroom. An online home building bookstore can save you money if you're willing to do the work.

Greg Vanden Berge is working on the internet to promote the education for creating simple to follow guides and home building books to help professional building contractors as well as the weekend warriors. He has just finished a Home Buyers Guide to take some of the frustration out of home shopping

If your looking for some more home inspection or home building ideas

Motorized Shades - Primary Benefits

1. Convenience. Raising and lowering a manual shade is easy enough if it is not too big. But if the shade is very large or there are 2, 3, 4 or more shades then it becomes more difficult and more time consuming. The convenience factors of motorized shades are important for several other reasons listed below.

a. Maximizing Views. Having motorized shades mean the difference between seeing a beautiful sunrise/sunset or missing it. Stunning vistas are rarely missed when opening or closing shades is as simple as pressing a button.

b. Security. Motorized shades can easily be set on a timer so that when guests are away from home for an extended period of time, shades are raised and lowered at various preset times. This gives the impression that someone is living in the house which deters would be thieves.

c. Conserving Energy. The heat gain from sunlight through windows during summer months is a major burden on air conditioning. The convenience of motorized shades makes saving energy much simpler. Preset timers obviate the need to remember to raise or lower shades for energy saving purposes.

d. Protecting Furniture, artwork and flooring. The sun's rays can do damage to interior furnishings, causing fading, cracking or warping. The convenience of motorized shades makes protecting furniture, artwork and flooring much simpler. Preset timers are also useful in this regard.

e. Many Windows and/or Large Windows. As the number and size of windows increases, the case for motorization becomes increasingly compelling. Some walls of windows are 20, 30 or even 60 feet in length which makes motorization a practical necessity.

f. Hard to reach windows. These skylight windows, second story openings or windows blocked by furniture or other obstructions are why motorized shades were first conceived. Obviously, these factors are still relevant today.

2. Child Safety. A shocking number of injuries and deaths result each year due to cords from manual window shades. The window shade industry's "Child Safety Month" is intended to address these hazards with safety clips and consumer awareness. The best solution is no cords at all, which is possible with motorized shades.

3. Unsightly Cords. Aesthetically, cords detract from the clean look of a window opening. Multiple shades mean multiple cords, pooling on the floor when fully open. Motorized window shades means no more unsightly control cords and open, clear views through windows.

4. Less Wear and Tear. Tangling and unfamiliar 'user abuse' to shades are the most common causes of service calls. The control mechanisms on manual shades, if used frequently (see convenience factor above), will break and can be costly to repair or replace.

5. They are cool! Functionally, motorized shades make a lot of sense and aesthetically, they are definitely preferable to manual shades. Let's not forget that they also have an impressive WOW Factor!

The author, Gavin Sword, is an owner of Automated Shading - New York Motorized Shades The company offers Motorized Shades in New York, Florida, (Miami, Naples, Tampa, Orlando), New Jersey and Pennsylvania.

Window Blinds May Be Useful For Tough Windows

Many homeowners and designers adore the appearance of window blinds, while others, however, may opt for a different type of window covering. Still, the challenge is controlling the amount of light that comes through the window. Some varieties of windows can be problematic for window blinds and shades. While it may seem possible to have window blinds, they may not be the most practical choice. This article will examine specific types of window problems with a light control solution presented for each. Window blinds may be the solution for some, while an alternative may be suggested for others.

One window that can present a difficulty is a sliding glass door. Not only are they large, but may sometimes they let the light just pour in. Window blinds can fit well in sliding glass doors but their size can make window blinds somewhat of an awkward choice. To compensate, count the number of glass panels you have and split the window shade accordingly. On a sliding glass door, one section stays static while the other moves freely. The best solution here is a two on one configuration. This is particularly true if many people will be using the door frequently, such as during summer parties and gatherings. This is an excellent choice if you prefer not to use window blinds for a larger space.

Another difficulty you may encounter is French doors. While window blinds look terrific on French doors, the door handle can sometimes prevent the vertical blind from working properly. In this situation, there are a number of options available. All products designed with a low profile head rail will work for this purpose. You will also require a device that will keep the veins of the vertical blind or other material to remain near to the door. In this way, any interference from the door handle will be minimized.

Bathrooms can be a tricky place to hang window blinds. Bathrooms are often rather damp, moist spaces. While you need ventilation to prevent the build up of mildew, you'll also want a sufficient amount of privacy while in your bathroom. Some window blinds may warp and crack over time as a result of the moisture in a bathroom. Obviously, you'll need to have window blinds that are able to withstand conditions such as these.

Nowadays there are skylights in a lot of homes. Skylights are a popular way to incorporate natural light and heat into your home. But at times, they can let in an overabundance of light, resulting in homes becoming too bright or overheated. The position of skylights could make fitting window blinds a challenge, but it can be done. One option offered by several companies is blinds that can be mechanically controlled. One such company is Sky Rise Skylight Systems. They stock shades and blinds that offer manual or motor control. These are an innovation that makes light control much easier, allowing you to get the most out of your skylight.

Some of us enjoy spectacular views out of large windows. But this scenery sometimes must be compromised in an effort to block the sun. Choosing window blinds that offer an abundance of width between the slats would be a great solution to this problem. These help to block the sun when necessary while preserving your home's amazing views.

It may be difficult to fit window blinds to the archways and other unusual shapes over doorways that allow light to pour into our homes. Some companies will make window blinds to fit your specific needs while others will need to be cut down to the appropriate size. They are now available with a pole-style control instead of more traditional cords. This is particularly useful when one part of a window is difficult to reach.

But you can find window blinds to fit nearly every window, although many of us may prefer something different. But window blinds are perfect treatments for windows and skylights. They can be custom made to fit any location you have in mind.

Today, window blinds are an easy to install home accessory, and to this end, Judith Persit has been writing about their selection and how wood blinds can be an attractive element for many buyers.

Build a Homemade Windmill - DIY Wind Generators For Under $100

Alternative energy options for homeowners are on the rise, just like the cost of conventional energy. You can build your own homemade windmill, also known as a wind generator and create your own free energy.

If you were to buy a commercial wind generator or solar array, it would cost you thousands of dollars. However, you can build your own wind generator for under $100 and generate over 1000 watts of power!

Homemade windmills are sprouting up all over the country and in areas with wind velocities as little as 6-8 mph. These wind generators create free electricity day and night, 365 days a year.
You can use this energy to power lights, computers, electronic equipment, pond pumps, night time lighting and for emergency power outages.

There is a ton of energy in the wind and the amazing thing is, power is proportional to the cube of speed. Meaning that if you double the speed of the wind, you actually quadruple the power output.
There are many good guides available to build your own homemade windmill, but a few of the things you want to look for are:

1. The homemade windmill plans have to be easy to read and follow.

2. The wind generator has to produce over 1000 watts of power.

3. It is possible to build the windmill for under $100 usd.

4. Not a copycat design of other wind generators.

5. Should be made from readily available materials.

6. It must be easy to build and assemble (even for us women).

7. It must be tough enough to endure heavy thunderstorms.

8. And the finished product has to look good. (Pesky neighbor approval).

If you keep these things in mind when looking for homemade windmill designs, you will not only have a better chance of completing your project successfully; you will also have a wind generator that packs a serious free energy punch.

Although wind generators do not have a huge foot print, they can have a pretty large sky print. The blades could reach nine feet or more from tip to tip and the tower reaches nearly twenty feet into the air. There are designs that reduce the blade diameter to six or seven feet and still produce the energy to make it worthwhile to build, so take your time looking for the homemade windmill best suited for your property.

Want to build your own wind powered generator? Of course you do! You can get a step by step guide at my website showing you how to build your own homemade windmill / wind generator and the greedy tax hungry government can't do a thing to stop you from enjoying FREE energy! Go to http://www.MylaMadson.com/offthegrid

Double Hung Window In Wall Framig

How You Can Easily Get a Walk-in Tub Installed

Imagine this scene- a person tired and weary after more than 13 hours in the office, rushes back home. It is a long, long drive. It had been an exhausting week and the person just craves a slow, relaxing bath. At home there is a spa installed with all the soaps, lotions and perfumes readily available. On reaching home, the person settles into the self-promised bath. A content smile touches the person's lips as he/she finally gets to relax the tired bones. Bath is just heavenly!

Not all people have this kind of luxury. Taking bath is not a divine experience for many. There are those who consider getting into a bathtub nothing short of a torture, and with good reason too. To consider their trauma, now consider this scenario:-

Imagine a person in his or her mid eighties. The stiff joint and the weakening knees are constant sources of pain. This person cannot move a muscle without a sigh. He/she needs a bath too, but just cannot think of enduring the pain of entering a bathtub. Once inside, there is yet another challenge- getting out. There is no way the person can mange this without help. He/she has to face the indignity of being carried and then lowered into the bathtub with specialized equipment!

The elderly, the ones on wheelchair, the physically challenged and others who do not have the freedom of movement due one or the other problem, find themselves in such a position everyday. Bathtub is a nightmare to them. But it need not be so. They can opt for walk-in tubs and baths.

Getting into a walk-in tub is very much like getting into a car. There is door, which open and the person can walk right in and sit. These days there are even special seats in the bathtubs for this purpose. Once the door close, there is no way the water can escape as it is both air and watertight. There are also special handle to facilitate the exit from the tub. With these facilities, walk-in tubs bring back the joy of bathing to those who suffering from different physical problems as well as the normal individuals (especially kids). Previously, the caretakers had to heave and sigh, while lifting their ward to the bath. They also can heave a sigh of relief as the days of carrying the defendant to the bath are over.

It is possible to change the normal bathtub to a walk-in tub. Within US you could purchase these from the store that sells other bath fixtures. Many of the bigger retail stores like Home Depot and other room stores have bathtubs that can be installed by you. These come with detailed guidelines. You could also opt for help and make use of the installation team, you may be charged a little extra for this. These teams are reputed to be very efficient.

Another alternative would be to hire a handyman. They might take a fee but a handyman takes the hassle out of installation.

Looking for information about walk-in tubs and showers

Theodor Cartman recommends different types of walk-in tubs and showers as the best option when buying.

Concrete

Bathroom Flooring Material

Bathroom Floors can be covered with wide variety of materials. Important things that one needs to consider while selecting bathroom flooring materials is affordability, water resistance and antislip qualities. Flooring bathroom with beautiful and suitable material can make it pretty. Right choice of material gives more impressive look to your bathroom.

Some Common Types of Bathroom Flooring Material

Following are some common examples of bathroom flooring materials.

• Natural Stone
• Lime Stone
• Marble
• Slate
• Granite
• Travertine

Natural Stone

It gives luxurious feel. It is expensive option. Repair cost is also high for damages such as staining and scratching. You can install it on your own but extreme care is necessary during cutting and matching of tiles.

Lime Stone

It is porous and soft in texture available in many light and neutral colors. It can vary in hardness. It retains the moisture and gets irreparable stains and scratches. It is not a good option for high transport area. Price is similar to marble. Professionals can install it properly because installation of limestone is very typical process in a sense that it can be broken easily due to improper installation.

Marble

Marble is made up of limestone treated to high temperature till recrystallization. This makes it hard. Sealing is required to make it resistant to stains. It is available in number of colors and veining. It is very smooth and gets very slippery when exposed to water. It is suggested to get it installed by professionals because improper installation can cause breaking and damage. It has to be treated with sealer on regular basis because it is highly prone to scratches and stains.

Slate

It is hard tile needs proper sealing for proper look and fitting. It is glamorous option. It is fine granular rock with textured and rustic appearance. It is non porous and best for washrooms. It is also available in good variety of hues and dark shades of black, gray, maroon, rust and green. It is one of the most durable bathrooms flooring material with more slip resistance.

Granite

It is drilled from very deep in earth. It is a kind of volcanic rock. It is beautiful flooring option. It is very hard but it is not resistant to stains. It is difficult to find similar pieces of granite due to variable veining and differences in stone color. It is very expensive. It is very durable and scratch resistant. It is also resistant to heat. It is porous and can get stains and absorbs moisture. To avoid this proper sealing is necessary after every six months. Proper installations can be done by professionals.

Travertine

This stone is commonly found in Italy. Chemically it is made up of calcium carbonate. It is available in several colors with uneven surface. These uneven surfaces can be filled. It is very durable bathroom flooring material and can resist to most cleaning products and it is also resistant to acids and basis.

If you want to know more information about bathroom remodeling options you can visit this site http://www.theyarelocal.com/articles/remodeling/bathroom_remodeling/index.php it will give you useful information and tips about bathroom remodeling.

Escondido Remodeling

How to Fix a Leaking Shower Head - Secrets From the Pros

How would you describe a dripping shower head- galling, grating or excruciatingly painful? The constant drip has the remarkable alacrity to get on one's nerves pretty quickly. But what most homeowners are not familiar with is the fact that this mundane leak in the bathroom can cause a severe drain on your resources and finances.

And before you begin to flip the yellow pages to ferret out details of a plumber, let me tell you that one does not require the competence or the efficiency of a plumbing professional to fix a leaking shower head. A brand new washer from a hardware store near your house, a screwdriver and an adjustable wrench are your tools in this war against the leaking shower head.

Tackle The Leak On A War Footing

So you believe that instead of burying your head in the sand in true ostrich fashion, the need of the hour is to plunge headlong into this pretty intractable situation? Well, your consternation can be attenuated to a considerable degree if you understand the root cause of the problem.

The leak could occur either at the point where the pipe and the shower head meet, or a clogged shower head may be the villain of the piece.

No matter what the diagnosis is, here's what you should do to ensure that the situation does not assume rampaging dimensions:

• Remove the shower head, at times with some help from an adjustable wrench.
• Remove and check the condition of the rubber gasket inside the shower head. If this part leaves a black residue on your hands, it's hinting at replacement.
• Using the right size, push the new part into place. The ring must be placed flat inside the shower head assembly.
• A few wraps of Teflon tape around the pipe threads in the same directions as the threads is important.
• Thread the shower back into place until it's fairly tight.
• It's now time to check for results. In case there's no leak, Bravo, you have succeeded.
• But if the leak persists, you may have to unscrew the head, and screw it back.

What remains is to enjoy the silence of empty (read: drip less) solitudes.

Learn exactly how to generate 100's or even 1000's of positively *BRILLIANT* Bathroom Remodeling Ideas ... FAST ! And here are 25 Dirt Cheap Home Improvement Ideas that could increase the value of your home by several $1000's ...

Painting Metal Siding

Bamboo Flooring - One of the Better Going Green Choices

Bamboo flooring is becoming one of the popular choices in hard flooring surfaces today. This is even more true for those homeowners who wish to use "green products" that are easily renewable.

An oak. maple, or pine tree needs to be cut down to get the benefit of lumber products. Another new tree needs to be replanted in it's place, taking many years to reach maturity.

Bamboo, on the other hand, will replenish itself and usually grows to stage that it may be harvested in about three years.

Bamboo flooring-What Does It Offer In Appearance?

When selecting bamboo flooring, the choices in appearance are many. Surprisingly, this product takes on the look of traditional wood flooring and can be found in many finishes.

There are shades as light as a pale bleached look. You will find all of the standard tones as well in light tones, medium tones with reddish overtones, dark tones like walnut, and even an almost black. The choices in appearance are many.

Bamboo, like other hard surface flooring will be beneficial to any in your household who suffer allergies. It will be easier to clean and maintain and keep your household environment more allergen free.

Shopping For Bamboo Flooring

When shopping for bamboo flooring, and especially if you are going to install it yourself, do be sure it is accompanied by manufacturer instructions for the installation process. Do not rely on a sales person. Read and follow the manufacturer instructions and recommendations to the letter. The manufacturer will recommend whatever products, tools, or methods are best used in the installation process to reach the most desirable outcome.

Most bamboo flooring, unlike standard laminates is either installed with glue or fasteners. Use the installation recommended, be sure underlayment is clean and flat, and acclimatize the product properly before beginning installation.

It is advisable to purchase bamboo in either the mid or upper price range. This is true of most flooring products in order to get a better quality that will provide the most in durability and performance.

With proper selection and installation you can enjoy the beauty of your bamboo floor for years and feel that you have made a step toward going green and still get the benefit of a beautiful wood look floor.

Find information on other flooring choices as well as a variety of bathroom remodeling tips and advice at=> http://www.bathroom-remodeling-hints.com

Horizontal Or Vertical Drywall

Moisture Against Gravity - Destroying Walls

Well I'm going to start this article with a little information on a job I did once.

I had been repairing a rental house for one particular homeowner for about three years when all of a sudden I got a phone call from him telling me the rental house was destroyed and he had never seen nothing like this. He sounded so upset over the phone I told him I would meet with him immediately.

On my way to the house I was trying to get an idea in my head what the house was going to actually look like. Since I have been repairing rental properties for over 20 years at this point of my career, nothing really shocked me. I had pretty much seen everything that could possibly be done to rental property by the tenants that lived there. There is a lot to be said about taking care of it as if it were your own.

He was waiting for me at the front door and he looked thoroughly disgusted. As I approached him he was shaking his head and yelling at the same time can you believe these people, can you believe what they did to my house. I was expecting to see the front door ripped off and all the windows broken out of the house but this wasn't the case.

As he led me through the home and I could see the usual clothing on the floor, broken cabinets, a few holes in the walls and of course that awful smell of mold and mildew. All of this stuff was nothing new to me because I'm the guy they call to fix it when a renter moves out of the property.

As I entered one of the bedrooms I got my first glimpse of something I had never seen before but heard stories about and could not believe my eyes. Looking at the walls in the bedroom about 3 feet from the floor all the way around the room, the plaster was soft. It actually looks like someone shoved popcorn into the wall somehow.

The homeowner wasn't even looking at this because of the rest of the damage in the home. I started to explain to him I'd never seen nothing like this but I could guess it was water damage somehow since the plaster was soft. I could actually stick my finger into the wall, that's how soft the plaster was.

My first thought was to examine the carpeting a little closer to see if it was wet. Well it was damp but it wasn't as wet as I would've expected it to be with the amount of water in the walls. With a little more home inspecting I had found the culprit, it was a broken water bed. The water bed was now in the backyard looking innocent.

I couldn't believe a broken water bed could do this much damage so I looked around for broken or leaking water pipes and could not find any. The other bad news I had to inform the homeowner was that the water had damage the bathroom and closet walls also. These walls of course were on the other side of the bathroom walls that were damaged.

Well the point of this story is that water will actually wick its way up or worked its way up into a wall. I had to remove 4 feet of drywall all the way around the room. The plaster or drywall actually acts like a sponge pulling the water into the walls. Hard to imagine that gravity in this case seems to reverse. I would've never thought that water would've traveled so far up the walls creating that much damage.

To repair the rental property I had to remove the damaged drywall, remove the carpeting, dry the wood framing out and put the whole thing back together.

I'm still amazed and will remember that project for as long as I live.

Greg Vanden Berge is working on the internet to promote the education for creating simple to follow guides and home building books to help professional building contractors as well as the weekend warriors. He is currently working on more Building and Remodeling Library and adding useful content to help solve problems created by the lack of construction knowledge in the building industry.

Visit us and get more information on House Water Damage

New Versus Old Lumber - Structural Failure

During my 30 years of remodeling and building new homes. I have ran across quite a bit of structural framing failures. I find myself answering this question a lot when explaining to a homeowner about the structural failure I am repairing on their home, "Why Didn't They Use Better Lumber" or " Why Didn't They Use Larger Lumber." I really have a hard time answering these questions because I honestly don't know the answer.

However I can try to use some logic and reason to give these people an answer that seems to make sense to both of us. Why didn't they use better lumber, quite simply because, with most older homes that were built before the 1970s they actually do have better lumber. Now you're probably thinking how can these homes have better lumber when the lumber is old versus the new lumber used in a brand new house.

Most of the structural repairs I have made over the years has nothing to do with the lumber and whether it was new or old. A large number of these repairs were caused by neglect and poor maintenance.

The lumber in most older houses are from older growth trees. Some of these trees were extremely large and only the premium parts of the trees were used. The premium lumber is cut farthest away from the center of the tree. Now the larger the tree it makes sense that there will be more premium lumber.

A large majority of the newer lumber used in home construction comes from trees about 6 inches in diameter. Now you're probably wondering how can they cut a 2 x 8 piece of lumber out of a 6 inch tree. Of course they cannot, the larger lumber comes from larger trees.

Most 2 x 4's that are less than 8 foot long can be cut from these trees. This scrap or waste that comes from cutting these two by fours will now go into engineered building materials like particleboard, oriented strand board and engineered beams. Another name for an engineered been would be a paralam.

I hope you're starting to get the picture now when it comes to using new or old lumber. There are companies that are going into old logging rivers and retrieving old growth lumber. These were logs that sank to the bottom of the river's and were never retrieved because it was too costly.

The old growth lumber is quite expensive. Who's to say what problems we will happen in the future from the newer products created with modern day technology. When it comes to building houses it is not an exact science and as contractors we have been repairing the damage from poor engineering for years.

When I use the word poor engineering I am not pointing fingers at engineers. We now have more knowledge about home construction then we had years ago.

New versus old lumber, who wins the battle. Only time will tell.

Greg Vanden Berge is working on the internet to promote the education for creating simple to follow guides and home building books to help professional building contractors as well as the weekend warriors. He is currently working on more building and Remodeling Library and adding useful content to help solve problems created by the lack of construction knowledge in the building industry.

Visit us and get more information on building and remodeling your homes and Structural Repairs.

Fireplace And Hearth Framing